|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
a FEATURES 1.8 V to 5.5 V Single Supply 2.5 On Resistance 0.75 On-Resistance Flatness -3 dB Bandwidth >200 MHz Rail-to-Rail Operation 6-Lead SC70 Package Fast Switching Times t ON 20 ns t OFF 6 ns Typical Power Consumption (<0.01 TTL/CMOS-Compatible APPLICATIONS Battery-Powered Systems Communication Systems Sample Hold Systems Audio Signal Routing Video Switching Mechanical Reed Relay Replacement CMOS 1.8 V to 5.5 V, 2.5 SPDT Switch/2:1 Mux In Tiny SC70 Package ADG779 FUNCTIONAL BLOCK DIAGRAM ADG779 S2 D S1 IN W) SWITCHES SHOWN FOR A LOGIC "1" INPUT GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The ADG779 is a monolithic CMOS SPDT (single-pole, double-throw) switch. This switch is designed on a submicron process that provides low power dissipation yet gives high switching speed, low on resistance and low leakage currents. The ADG779 operates from a single supply range of 1.8 V to 5.5 V, making it ideal for use in battery-powered instruments and with the new generation of DACs and ADCs from Analog Devices. Each switch of the ADG779 conducts equally well in both directions when on. The ADG779 exhibits break-before-make switching action. Because of the advanced submicron process, -3 dB bandwidth of greater than 200 MHz can be achieved. The ADG779 is available in a 6-lead SC70 package. 1. Tiny 6-Lead SC70 Package. 2. 1.8 V to 5.5 V Single Supply Operation. The ADG779 offers high performance, including low on resistance and fast switching times, and is fully specified and guaranteed with 3 V and 5 V supply rails. 3. Very Low RON (5 max at 5 V, 10 max at 3 V). At 1.8 V operation, RON is typically 40 over the temperature range. 4. On-Resistance Flatness (RFLAT(ON)) (0.75 typ). 5. -3 dB Bandwidth >200 MHz. 6. Low Power Dissipation. CMOS construction ensures low power dissipation. 7. 14 ns Switching Times. REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2001 ADG779-SPECIFICATIONS1 (V Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On Resistance Match Between Channels (RON) On-Resistance Flatness (RFLAT(ON)) LEAKAGE CURRENTS2 Source OFF Leakage IS (OFF) Channel ON Leakage ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current IINL or IINH DYNAMIC CHARACTERISTICS2 tON tOFF Break-Before-Make Time Delay, tD Off Isolation 0.75 DD =5V 10%, GND = 0 V) B Version -40 C to 25 C +85 C 0 V to VDD 2 .5 5 6 0.1 0.8 1.2 0.01 0.01 0.05 0.05 Unit V typ max typ max typ max nA typ nA typ Test Conditions/Comments VS = 0 V to VDD, IS = -10 mA, Test Circuit 1 VS = 0 V to VDD, IS = -10 mA VS = 0 V to VDD, IS = -10 mA VDD = 5.5 V VS = 4.5 V/1 V, VD = 1 V/4.5 V, Test Circuit 2 VS = VD = 1 V, or VS = VD = 4.5 V, Test Circuit 3 2.4 0.8 0.005 0.1 14 20 3 6 8 1 -67 -87 -62 -82 200 7 27 V min V max A typ A max ns typ ns max ns typ ns max ns typ ns min dB typ dB typ dB typ dB typ MHz typ pF typ pF typ VIN = VINL or VINH Channel-to-Channel Crosstalk Bandwidth -3 dB CS (OFF) CD, CS (ON) POWER REQUIREMENTS IDD RL = 300 , CL = 35 pF VS = 3 V, Test Circuit 4 RL = 300 , CL = 35 pF VS = 3 V, Test Circuit 4 RL = 300 , CL = 35 pF, VS1 = VS2 = 3 V, Test Circuit 5 RL = 50 , CL = 5 pF, f = 10 MHz RL = 50 , CL = 5 pF, f = 1 MHz, Test Circuit 6 RL = 50 , CL = 5 pF, f = 10 MHz RL = 50 , CL = 5 pF, f = 1 MHz, Test Circuit 7 RL = 50 , CL = 5 pF, Test Circuit 8 f = 1 MHz f = 1 MHz VDD = 5.5 V Digital Inputs = 0 V or 5 V 0.001 1.0 A typ A max NOTES 1 Temperature ranges are as follows: B Version, -40C to +85C. 2 Guaranteed by design, not subject to production test. Specifications subject to change without notice. -2- REV. 0 SPECIFICATIONS Parameter ANALOG SWITCH Analog Signal Range On Resistance (RON) On Resistance Match Between Channels (RON) 1 ADG779 (VDD = 3 V 10%, GND = 0 V) B Version -40 C to 25 C +85 C 0 V to VDD 7 10 0.1 0.8 2.5 0.01 0.01 0.05 0.05 Unit V typ max typ max typ nA typ nA typ Test Conditions/Comments 6 VS = 0 V to VDD, IS = -10 mA, Test Circuit 1 VS = 0 V to VDD, IS = -10 mA VS = 0 V to VDD, IS = -10 mA VDD = 3.3 V VS = 3 V/1 V, VD = 1 V/3 V, Test Circuit 2 VS = VD = 1 V, or VS = VD = 3 V, Test Circuit 3 On-Resistance Flatness (RFLAT(ON)) LEAKAGE CURRENTS Source OFF Leakage IS (OFF) Channel ON Leakage ID, IS (ON) DIGITAL INPUTS Input High Voltage, VINH Input Low Voltage, VINL Input Current IINL or IINH DYNAMIC CHARACTERISTICS2 tON tOFF Break-Before-Make Time Delay, tD Off Isolation 2 2.0 0.8 0.005 0.1 16 24 4 7 8 1 -67 -87 -62 -82 200 7 27 V min V max A typ A max ns typ ns max ns typ ns max ns typ ns min dB typ dB typ dB typ dB typ MHz typ pF typ pF typ VIN = VINL or VINH Channel-to-Channel Crosstalk Bandwidth -3 dB CS (OFF) CD, CS (ON) POWER REQUIREMENTS IDD RL = 300 , CL = 35 pF VS = 2 V, Test Circuit 4 RL = 300 , CL = 35 pF VS = 2 V, Test Circuit 4 RL = 300 , CL = 35 pF VS1 = VS2 = 2 V, Test Circuit 5 RL = 50 , CL = 5 pF, f = 10 MHz RL = 50 , CL = 5 pF, f = 1 MHz, Test Circuit 6 RL = 50 , CL = 5 pF, f = 10 MHz RL = 50 , CL = 5 pF, f = 1 MHz, Test Circuit 7 RL = 50 , CL = 5 pF, Test Circuit 8 f = 1 MHz f = 1 MHz VDD = 3.3 V Digital Inputs = 0 V or 3 V 0.001 1.0 A typ A max NOTES 1 Temperature ranges are as follows: B Version, -40C to +85C. 2 Guaranteed by design, not subject to production test. Specifications subject to change without notice. REV. 0 -3- ADG779 ABSOLUTE MAXIMUM RATINGS 1 (TA = 25C unless otherwise noted) TERMINOLOGY VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +7 V Analog, Digital Inputs2 . . . . . . . . . . -0.3 V to VDD + 0.3 V or 30 mA, Whichever Occurs First Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA (Pulsed at 1 ms, 10% Duty Cycle max) Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 30 mA Operating Temperature Range Industrial (B Version) . . . . . . . . . . . . . . . . . -40C to +85C Storage Temperature Range . . . . . . . . . . . . . -65C to +150C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150C SC70 Package, Power Dissipation . . . . . . . . . . . . . . . . 315 mW JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 332C/W JC Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 120C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220C NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Only one absolute maximum rating may be applied at any one time. 2 Overvoltages at IN, S or D will be clamped by internal diodes. Current should be limited to the maximum ratings given. Table I. Truth Table ADG779 IN 0 1 Switch S1 ON OFF Switch S2 OFF ON Most Positive Power Supply Potential. Ground (0 V) Reference. Source Terminal. May be an input or output. Drain Terminal. May be an input or output. Logic Control Input. Ohmic resistance between D and S. On resistance match between any two channels i.e., RON max - RON min. RFLAT(ON) Flatness is defined as the difference between the maximum and minimum value of on resistance as measured over the specified analog signal range. Source Leakage Current with the switch "OFF." IS (OFF) ID, IS (ON) Channel Leakage Current with the switch "ON." VD (VS) Analog Voltage on Terminals D, S. CS (OFF) "OFF" Switch Source Capacitance. CD, CS (ON) "ON" Switch Capacitance. tON Delay between applying the digital control input and the output switching on. tOFF Delay between applying the digital control input and the output switching off. tD "OFF" time or "ON" time measured between the 90% points of both switches, when switching from one address state to another. Crosstalk A measure of unwanted signal that is coupled through from one channel to another as a result of parasitic capacitance. Off Isolation A measure of unwanted signal coupling through an "OFF" switch. On Response The frequency response of the "ON" switch. On Loss The loss due to the "ON" resistance of the switch. VDD GND S D IN RON RON PIN CONFIGURATION 6-Lead SC70 IN 1 VDD 2 GND 3 6 S2 D S1 ADG779 TOP VIEW (Not to Scale) 5 4 ORDERING GUIDE Model ADG779BKS Temperature Range -40C to +85C Package Description SC70 (Plastic Surface Mount) Package Option KS-6 Branding Information* SKB *Brand = Brand on these packages is limited to three characters due to space constraints. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADG779 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE -4- REV. 0 Typical Performance Characteristics- ADG779 6.0 5.5 5.0 4.5 4.0 3.5 RON - 0.15 VDD = 2.7V TA = 25 C 0.10 VDD = 5V VD = 4.5V/1V VS = 1V/4.5V VDD = 3.0V CURRENT - nA VDD = 4.5V 3.0 2.5 2.0 1.5 1.0 0.5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VD OR VS - DRAIN OR SOURCE VOLTAGE - V VDD = 5.0V ID, I S (ON) 0.05 0 IS (OFF) -0.05 0 10 20 30 40 50 60 TEMPERATURE - C 70 80 90 TPC 1. On Resistance as a Function of VD (VS) Single Supplies TPC 4. Leakage Currents as a Function of Temperature 6.0 5.5 5.0 4.5 4.0 -40 C 3.5 +85 C +25 C CURRENT - nA 0.15 VDD = 3V VDD = 3V VD = 3V/1V VS = 1V/3V 0.10 RON - 3.0 2.5 2.0 1.5 1.0 0.5 0 0.05 ID, I S (ON) 0 IS (OFF) -0.05 0 0.5 1.0 1.5 2.0 2.5 VD OR VS - DRAIN OR SOURCE VOLTAGE - V 3.0 0 10 20 30 40 50 60 TEMPERATURE - C 70 80 90 TPC 2. On Resistance as a Function of VD (VS) for Different Temperatures VDD = 3 V 6.0 5.5 5.0 4.5 4.0 3.5 +85 C VDD = 5V TPC 5. Leakage Currents as a Function of Temperature 10m VDD = 5V 1m 100 I SUPPLY - A 3.0 3.5 4.0 4.5 5.0 RON - 10 1 3.0 2.5 2.0 1.5 1.0 +25 C -40 C 100n 10n 0.5 0 0 0.5 1.0 1.5 2.0 2.5 1n 1 10 100 VD OR VS - DRAIN OR SOURCE VOLTAGE - V 1k 10k 100k FREQUENCY - Hz 1M 10M 100M TPC 3. On Resistance as a Function of VD (VS) for Different Temperatures VDD = 5 V TPC 6. Supply Current vs. Input Switching Frequency REV. 0 -5- ADG779 -30 VDD = 5V, 3V -40 -50 OFF ISOLATION - dB 0 VDD = 5V ON RESPONSE - dB 100k 1M 10M FREQUENCY - Hz 100M 0 -60 -70 -80 -90 -100 -110 -120 -130 10k -2 -4 -6 10k 100k 1M 10M FREQUENCY - Hz 100M TPC 7. Off Isolation vs. Frequency TPC 9. On Response vs. Frequency -30 VDD = 5V, 3V -40 -50 CROSSTALK - dB -60 -70 -80 -90 -100 -110 -120 -130 10k 100k 1M FREQUENCY - Hz 10M 100M 0 TPC 8. Crosstalk vs. Frequency -6- REV. 0 ADG779 Test Circuits IDS V1 S VS D VS IS (OFF) A S D ID (OFF) A VD ID (ON) S VS D A VD RON = V1/I DS Test Circuit 1. On Resistance Test Circuit 2. Off Leakage Test Circuit 3. On Leakage 0.1 F VDD VIN VDD 50% 90% 50% 90% S VS IN GND D RL 300 CL 35pF VOUT VOUT tON tOFF Test Circuit 4. Switching Times 0.1 F VDD VIN D D2 RL2 300 GND CL2 35pF VOUT VS1 VS2 VIN S1 S2 IN VDD 0V 50% 0V 50% 50% 50% VOUT tD tD Test Circuit 5. Break-Before-Make Time Delay, tD VDD VDD 0.1 F NETWORK ANALYZER S IN D VIN GND RL 50 VOUT 50 NETWORK ANALYZER VOUT RL 50 0.1 F VDD 0.1 F VDD S1 S2 D VDD VDD S R 50 NETWORK ANALYZER 50 VS IN D 50 VS VOUT 50 VS IN GND VIN GND RL 50 VOUT OFF ISOLATION = 20 LOG VS CROSSTALK = 20 LOG CHANNEL-TO-CHANNEL VOUT VS INSERTION LOSS = 20 LOG VOUT WITH SWITCH VOUT WITHOUT SWITCH Test Circuit 6. Off Isolation Test Circuit 7. Channel-to-Channel Crosstalk Test Circuit 8. Bandwidth REV. 0 -7- ADG779 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 6-Lead Plastic Surface Mount Package (SC70) (KS-6) C02491-1.5-7/01(0) 8 0.007 (0.18) 0 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.087 (2.20) 0.071 (1.80) 0.053 (1.35) 0.045 (1.15) PIN 1 6 1 5 2 4 3 0.094 (2.40) 0.071 (1.80) 0.026 (0.65) BSC 0.051 (1.30) BSC 0.039 (1.00) 0.031 (0.80) 0.004 (0.10) 0.000 (0.00) 0.043 (1.10) 0.031 (0.80) 0.012 (0.30) SEATING 0.006 (0.15) PLANE -8- REV. 0 PRINTED IN U.S.A. |
Price & Availability of ADG779 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |